6) Question / Partitions: solutions phonic
Hello and thank you in advance for the advice,
We plan with my wife to change our current home. We're going to rebuild a part of our house by adding a level. The construction will be aerated concrete.
We have 3 children and my fear is the spread of rumors.
For partitioning I need advice as to the type of product to use to separate rooms including 3 bedrooms, 1 toilet and 1 bathroom. And the second question is which technique to put in place during the implementation to avoid maximum noise from spreading through the walls and the floor.
. What I want to know is whether there should be an insulator between the ground and the low rail, between the ceiling and the top rail and the amount between the wall and knowing that all this is screwed and therefore there is risk of spreading noise by vibration.
Then I asked whether I pass the plates to provide rigidity and provide better sound insulation plate what quality should I use? Is it necessary to put the band at the junction of the first plates? And how to solve the problem of aesthetics on the thickness for junctions between the doors and walls since the thickness is greater than 72 is no possibility of recovery doors?
To avoid the propagation of noise through the ceiling I was also told that it was better a ceiling covered auto. What exactly is and what do you think?
Thank
6) Response / Partitions: solutions phonic
Bj: DTU foam tape in wet areas as well as a plastic film, the foam would not be bad for you . . Can you get from your dealer materials. There are doors to block the collection procedures for double-skin walls, but not in standard will require that your provider orders or have them made by a carpenter. I know the sound insulation it is not a special plate, you just take the BA 13. If you want the beefier you can put the BA18 or 3 instead of 2 plates. The first plate does not need joint tape. If you want to use a standard door partition 70 or 50 you have to screw a plate around the door frame on the 3 sides that makes the minimum width of partition and after your next set-metal structure and the 2 amounts the piece of rail of the transom on these plates. One side of the partition plates so will put it behind the cover and seal the other side it will press against the plasterboard screwed against the door after he's done there will be bands to seal the edges. A cap is said to be self raised a ceiling made with amounts, but you can do it both rails ceiling F530 and angles. It is important is that the cap is cut by the partition. For the safety issue should not act as if you were going to build a recording studio, you should also be able to hear what happens on the other side of the house anyway!. A + Jorge
Hello and thank you in advance for the advice,
We plan with my wife to change our current home. We're going to rebuild a part of our house by adding a level. The construction will be aerated concrete.
We have 3 children and my fear is the spread of rumors.
For partitioning I need advice as to the type of product to use to separate rooms including 3 bedrooms, 1 toilet and 1 bathroom. And the second question is which technique to put in place during the implementation to avoid maximum noise from spreading through the walls and the floor.
. What I want to know is whether there should be an insulator between the ground and the low rail, between the ceiling and the top rail and the amount between the wall and knowing that all this is screwed and therefore there is risk of spreading noise by vibration.
Then I asked whether I pass the plates to provide rigidity and provide better sound insulation plate what quality should I use? Is it necessary to put the band at the junction of the first plates? And how to solve the problem of aesthetics on the thickness for junctions between the doors and walls since the thickness is greater than 72 is no possibility of recovery doors?
To avoid the propagation of noise through the ceiling I was also told that it was better a ceiling covered auto. What exactly is and what do you think?
Thank
6) Response / Partitions: solutions phonic
Bj: DTU foam tape in wet areas as well as a plastic film, the foam would not be bad for you . . Can you get from your dealer materials. There are doors to block the collection procedures for double-skin walls, but not in standard will require that your provider orders or have them made by a carpenter. I know the sound insulation it is not a special plate, you just take the BA 13. If you want the beefier you can put the BA18 or 3 instead of 2 plates. The first plate does not need joint tape. If you want to use a standard door partition 70 or 50 you have to screw a plate around the door frame on the 3 sides that makes the minimum width of partition and after your next set-metal structure and the 2 amounts the piece of rail of the transom on these plates. One side of the partition plates so will put it behind the cover and seal the other side it will press against the plasterboard screwed against the door after he's done there will be bands to seal the edges. A cap is said to be self raised a ceiling made with amounts, but you can do it both rails ceiling F530 and angles. It is important is that the cap is cut by the partition. For the safety issue should not act as if you were going to build a recording studio, you should also be able to hear what happens on the other side of the house anyway!. A + Jorge
0 comments:
Post a Comment